CE marking- EMC and radio tests, EMF

CE marking - EMC and radio frequency tests

Measurement at 3m in Fully Anechoic Room (FAR)

A Faraday room with ferrite tiles and pyramidal absorbers builded to be a full anechoic room can comply the site attenuation of an open area test site.
The emission measurements are equivalent and have the advantage to be also insulated from exterior sources of electromagnetic noise.
We obtain faster measurments in FAR

A FAR can be used for EMC tests (emission, immunity) and radio frequency tests.

• Radiated emission type CISPR 16-1-4, ANSI C63.4 from 30MHz to 26GHz 
• Radiated immunity tests type IEC 61000-4-3, EN 61000-4-3 from 80 MHz to 6 GHz 
• Radio emission type EN 300 330 / EN300220 / EN300440

Measurement at 3 or 10m in our large semi-anechoic chamber

With its dimension (15m x 10m x 7m),  our Faraday room dedicated to the measurements at 3 or 10m worth its name of "large room".
With its large shielded door, these room can be used to test huge equipments.

These room can be used for EMC tests (emission, immunity) and radio frequency tests.

• Radiated emission type CISPR 16-1-4, ANSI C63.4 from 30MHz to 26GHz (possibilty to extend to 40 GHz)
• Radiated immunity tests type IEC 61000-4-3, EN 61000-4-3 from 80 MHz to 6 GHz (possibilty to extend to 40 GHz)
• Radio emission type EN 300 330 / EN300220 / EN300440

Measurement at 3 or 10m in our open area test site 

Reference measurments for the emission tests, the equipment under tests is installed on a turntable  (0 to 360 degrees), the height of the antenna is adjusted between 1 to  4m. For each frequency detected, the position of the turntable and the height of the antenna are optimized to obtain the high value of the RF field.
The ambiant radio frequency spectrum add an electromagnetic noise and complexify the measure and its duration. 

Our open area test site is near our lab.

It is used for EMC emission tests and radio frequency tests.

• Radiated emission type CISPR 16-1-4 from 30MHz to 1GHz 
• Radio emission type EN 300 330 / EN300220 / EN300440

Electrical tests, conducted emission and immunity, ...

Flickers et harmonics EN 61100 3-2 & 3-3 and EN 61100 3-11 & 3-12

• Single and three phase 16 A
• Single and three phase 32A

Conducted emission type CISPR 16-1-4/CISPR 11/CISPR 22/CISPR 14 from 9kHz to 30MHz:

• LISN 1 phase - 10A 
• LISN 3 phases - 100A
• LISN 3 phases - 400A
• 1 to 6m  cable slide bar for disturbing power emission

Conducted immunity:

• EN 61100 4-6 - 10Veff from150kHz to 230MHz.

Magnetic immunity:

• EN 61100 4-8 Magnetic field by immersion 30A/m 50/60Hz.

Electrical tests:

• EN 61100 4-2 Electrostatic discharge up to 30kV.
• EN 61100 4-4 CDN 3 phases 30A, amplitude burst 4.4kV.
• EN 61100 4-4 CDN 3 phases 100A, amplitude burst 4.4kV.
• EN 61100 4-5 CDN 3 phases 25A amplitude 6.6 KV.
• EN 61100 4-5 CDN 3 phases 150A amplitude 6.6 KV.
• EN 61100 4-11 1 phase, 3 phases and DC.

A recognized expertise in addition to our facilities 

A know-how in technical assistance and advices to solve design issue.
Recommandations according the state of the art to take into account the EMC phenomena, including EMF.
Intervention in France and in the world on disturbed sites (EMC). 

Standards - CE marking and international regulations

EMC directive 2004/108/EC

EN 55016-2-1 / EN 55016-2-2 / EN 55016-2-3
EN 61000-3-2 / EN 61000-3-3 / EN 61000-3-11 / EN 61000-3-12
EN 61000-4-(2 à 6, 8 à 13, 16 et 17)
EN 61000-6-(1 à 4)
FCC PART 15 / ICES-003 / NMB-003 / ANSI C63.4

Medical devices directive 93/42/EEC

CEI / EN 60601-1-2

R&TTE 99/5/EC directive

EN 301 489-X and associated standards ETS
EN 300 330 / EN300220-1 et-2 / EN302291-1et-2 / EN301511 / EN300328 / EN 301908-1

Board of test method